16-LED NIGHT RIDER

Description The bi-directional sequencer uses a 4 bit binary up/down counter (CD4516) and two “1 of 8 line decoders" (74HC138 or 74HCT138) to generate the popular Night Rider display. A Schmitt Trigger oscillator provides the clock signal for the counter and the rate can be adjusted with the 500k pot. Two additional Schmitt Trigger inverters are used as a SET/RESET latch to control the counting direction (up or down). Be sure to use the 74HC14 and not the 74HCT14, the 74HCT14 may not work due to the low TTL input trigger level. When the highest count is reached (1111) the low output at pin 7 sets the latch so that the UP/DOWN input to the counter goes low and causes the counter to begin decrementing. When the lowest count is reached (0000) the latch is reset (high) so that the counter will begin incrementing on the next rising clock edge. The three lowest counter bits (Q0, Q1, Q2) are connected to both decoders in parallel and the highest bit Q3 is used to select the appropriate decoder. to Index 555 SCHMITT Circuit Diagram

SEQUENCER OUTPUT LED

The secret to designing a circuit is to look at the final design and ask: "is this component necessary?" Try removing a component and see if the circuit still works. Keep doing this with all the components. The circuit above was published in an Indian magazine with over 1,000,000 readers. The faults were obvious. How these faults passed an editorial committee is beyond me. They are showing very poor design-leadership in allowing this oversight to be published. The faults are technical but are obvious to anyone who has constructed the circuit and experimented with it. Obviously the circuit has never been assembled with anyone with technical expertise. Circuit Diagram

10 OUTPUT LED SEQUENCER

Description Here is 10 output LED sequencer. After the last LED is illuminated, the circuit is reset. This circuit is build around readily available, low cost components - a 555 and decade counter CD4O1 7. The timer IC NE555 is wired as an astable multivibrator that produces 6Hz clock at its output pin 3. The 4017 is a CMOS decade counter with 10 outputs. Inputs include a CLOCK (Pin 14), a RESET (Pin 15), and a CLOCK INHIBIT (Pin 13). The clock input connects to a Schmitt trigger for pulse shaping and allows slow clock rise and fall times (not needed in our case). The counter advances one output at the rising edge of the clock signal if the CLOCK INHIBIT line is low. A high RESET signal resets the counter to the zero output. The circuit may be configured for counts less than 10 by connecting RESET to an output pin (one after the desired count). Thus, a five stage sequencer can be made by connecting pin 15 to pin 1. A CARRY-OUT signal (pin 12) can be used to clock subsequent stages in a multi-device counting chain.The output from 1C2 pin 3 is connected to clock pin (pin 14) of the IC3 for sequencing operations. NPN transistors Q1- Q10 are used to increase the output current for the LEDs which is set by the common 150 ohm resistor. In the circuit, only one of the outputs is HIGH at any one time and the output advances by one count with every clock pulse. Circuit Diagram

Voice manipulation device

Circuit Description

 

Although this kind of voice effect can be obtained by means of some audio computer programs,
a few correspondents required a stand-alone device, featuring microphone input and line or
loudspeaker outputs.
This design fulfills these requirements by means of a variable gain microphone preamplifier built
around IC1A, a variable steep Wien-bridge pass-band filter centered at about 1KHz provided by
IC1B and an audio amplifier chip (IC2) driving the loudspeaker.
This circuit was intended to be powered by a 9V PP3 battery, but any dc power supply in the 6 -
12V range can be used successfully.

        Circuit diagram:

 

Parts List:
P1______________10K Log. Potentiometer
R1,R10__________10K 1/4W Resistors
R2_______________1K 1/4W Resistor
R3______________50K 1/2W Trimmer Cermet or Carbon
R4,R6,R7,R14___100K 1/4W Resistors
R5______________47K 1/4W Resistor
R8______________68K 1/4W Resistor
R9_______________2K2 1/2W Trimmer Cermet or Carbon
R11_____________33K 1/4W Resistor
R12_____________18K 1/4W Resistor
R13_____________15K 1/4W Resistor
C1,C2,C3,C8,C9_100nF 63V Polyester Capacitors
C4______________10μF 25V Electrolytic Capacitor
C5_____________220nF 63V Polyester Capacitor (Optional, see Notes)
C6_______________4n7 63V Polyester Capacitor
C7______________10nF 63V Polyester Capacitor
C10____________220μF 25V Electrolytic Capacitor
IC1___________LM358 Low Power Dual Op-amp
IC2_________TDA7052 Audio power amplifier IC
MIC1__________Miniature electret microphone
SPKR______________8 Ohm Small Loudspeaker
SW1____________DPDT Toggle or Slide Switch
SW2,SW3________SPST Toggle or Slide Switches
J1____________6.3mm or 3mm Mono Jack socket
B1_______________9V PP3 Battery (See Notes)
Clip for PP3 Battery